# HB000320 - HYPER 9 PRO CAR KIT


Giá : 9,870,000 VNĐ


 

HB000320 1/8 HYPER 9 PRO CAR(M9-S)

 

 

OVERVIEW:

  

 

  The Hyper 9 is a completely new design from the ground up with many new and innovative ideas. Several criteria were set and met in this new design. Weight was number one and always a concern with every part designed for the buggy. Next, in order of importance, was side to side balance, low center of gravity, ground clearance, all on as narrow a chassis as possible.

  On the performance side, the buggy had to accelerate, corner, jump and land better than any other buggy on the market. Here we shall explain how we acheived those goals.

 

  Keep it Light
  The number one goal in the new design was to keep the Hyper 9 light weight. Reduced weight equals faster acceleration and cornering speed. Smaller 8x14mm bearings have been used throughout the chassis (except for the rear 8x16mm wheel hub bearings). The number of screws was reduced, the plastic was reduced and the amount of aluminum used was reduced. The part count in total has also been reduced.

  Chassis Balance
  The engine was moved toward the center by using a 40 tooth spur gear and keeping the 13 tooth clutch bell. In doing this, the center drive line angles are also straighter, reducing scrub on the joint pins.

  Moving the engine closer to the center drive line did not allow room for the rear brake on the center outdrive, so the disk was moved to the rear pinion shaft. The engine was then angled 25 degrees toward the center for four reasons.

1.       Allowed clearance between engine mount flange and center drive shaft.

2.       Moved weight toward center of chassis.

3.       Lowered center of gravity.

4.       Pulled pipe toward center of chassis. All this combined with the asymmetric aluminum chassis plate balances the buggy left to right with a half tank of fuel.

  Ground Clearance
  Ground clearance has been something overlooked for years by most 1/8 scale designs. The chassis has been shortened for clearance front and rear while keeping the same wheel base as the Hyper 8.5. The bend for the 10 degree kick up in the nose has been moved forward as much as possible to increase clearance. The aluminum chassis plate has been reduced in size, cut on all four corners, and the side guards have been angled up for extra clearance. This is especially important when the chassis leans and squats while exiting a corner.

  Gearing
  The buggy accelerates and has greater top end speed because of the 11/43 gear combination at the front/rear gear boxes and the 13/40 combination at the center differential. The faster spinning center differential also reduces the torque effect of the engine.

  Better Cornering and Better Jumping
  Most of the testing for the new Hyper 9 was setting roll center points front and rear for better balance through the corners and better jumping. The new buggy has better matching roll centers that make the buggy more consistent as the track conditions change.

  The Hyper 9 runs stiffer front springs, and the front end rides higher. This, combined with the reduced weight, allows the buggy to jump further (chassis does not scrub off speed on face of jump) and recovers from landings faster (chassis does not bottom out as hard).

 

 

 

FEATURES: 

 

 

    1. No, E-clips, Inboard hinge pins in captive supports front and rear. Outboard hinge pins secured with setscrew

   2. New front and rear brake sets

   3. T-shape linkage arm for 25° slanted engine and brake set

   4. One-piece battery box base and side guard for lower centre of gravity

   5. Big bore threaded body shock absorbers

   6. Lightweight one-piece wing and mount for improved weight distribution

   7. New servo saver and steering assembly for improved reliability and adjustment

   8. Unique 25° slanted engine to balance cars centre of gravity

   9. Titanium turnbuckles

 10. Smart pull for fuel tank to improve re-fueling

 11. Reduced weight, ground clearance & chassis width all make for improved jumping and cornering ability

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sản phẩm khác

HYPER 8 PRO KIT

 

Thuộc thể loại buggy 1/8. Sản phẩm bao gồm chỉ 1 kit ...các bạn cần trang bị thêm bộ điều khiển, máy nổ (size 21), và một số dụng cụ cần thiết...

 


Giá : 9,165,000 VNĐ

HYPER GPX4 PRO CAR

 

Sản phẩm chỉ bao gồm 1 kit, cấu tạo và chi tiết của xe được thiết kế đúng chuẩn mực của 1 xe Pro...Bạn chỉ cần trang bị thêm bộ điều khiển, máy nổ, và một số dụng cụ cần thiết ...


Giá : 5,875,000 VNĐ

HYPER 8.5 PRO CAR

 

Thuộc thể loại buggy 1/8. Sản phẩm bao gồm chỉ 1 kit ...các bạn cần trang bị thêm bộ điều khiển, máy nổ (size 21-30),điều khiển và một số dụng cụ cần thiết...


Giá : 8,695,000 VNĐ